Follow us on
[Your Basket]
[Search]
Product Categories
Computer Viewing
How We See Depth
Slide Bar
Antique
Scan Roll
Hyper-View
HyperView Inst.
Cleaning POV
3Dfacts
FAQ
Links Page
Clip-on 3-D Viewer
Canon Twin Rig
Stereocard B&W
Webmasters
Stereo Base Calculator
Replacing Kodaslide Lens
Wheatstone Directions
Change Scope Lens
Webring Page
Canon Twin
StereoCard Printing
8P Modification
Dual Cable Release
Tips
Glossary
Home Up
Home
About Us
Contents
News
Tech Support FAQ
Reel 3D Cross Ref
Services
Feedback
Order Info
Price List

Instructions for Preparing Stereo Photographs for Viewing with the Hyper-View Large Format Viewer

Hyperview Page

The Hyper-View Large Format viewer is made for viewing images from about 7 inches to about 11 inches wide. Images can be mounted using comparable methods to that used on any stereo cards. For archival reasons it is recommended that the images be mounted on acid free matboard. Use either dry mount tissue with the appropriate press or Positionable Mounting Adhesive by 3M for mounting.

After fixing the adhesive to the back of the prints trim as directed below.

    1. Start by trimming the bottoms even. An easy way to do this is place a straight edge at the bottom of both images, move the images around so they are in the same relative position, and trim with a razor blade.

    2. Trim the right edge of the left print perpendicular to the bottom. You may trim it wherever you would like, but generally as close to the edge as possible.

    3. Identify the nearest point in the scene (in the left print) and measure from it to the edge just trimmed.

    4. In the right print, locate the near point as in step 3. and measure to the right the same distance as found in step 3. Trim the right print at this point.

    5. Next trim the left edge of the right print cropping it to your desired position (probably close to the edge).

    6. Measure the width of the right print and trim the left print to the same width.

    7. Trim the tops of both prints so they are the same height.

All that is left now is to position the prints on the mat and adhere them. If the prints are larger than about 9 inches position them fairly close together, ~1/4 inch. Smaller prints should be placed farther apart. Adjust the prints before mounting to estimate the best separation. Most likely, it will be found that one will end up with an infinity separation of about 10 inches. (That is, the image will probably be easiest to view if the corresponding infinity points are about 10 inches apart).

Framing and putting under glass may protect the prints. Lighting becomes critical because of potential reflections in the glass. The ideal situation is to have a strong light right above the image so that the reflection will not be in visible to the viewer. Another solution is to use a type of glass called Denglas. This glass has an anti-reflective coating such as camera lenses use, and reflections almost disappear. Unfortunately it is very expensive (approximately $60 for a piece large enough for this purpose). There is no other type of anti-reflective glass that maintains the sharpness of the image under it.

Avoiding touching the mirrors. If they do need cleaning, try using a piece of soft cotton material with lens cleaner. If the mirrors become damaged, you can return the viewer to us and we will replace the mirrors for a nominal fee.

Technical note: The width at which the eye paths are parallel (assuming an eye separation of 2 1/2 inches) with the Hyper-View Viewer is 11 5/8 inches. Although it is sometimes possible to view images with a larger infinity separation than this, it is difficult for most people. It is suggested that limit the infinity separation to 11 5/8 inches for images intended to be viewed with this viewer.

[ Order ] 

Berezin Stereo Photography Products 21686 Abedul,  Mission Viejo, CA 92691 USA  (949) 215-1554  We accept PayPal! 

Please contact us with questions or comments about this web site. All content, unless otherwise noted 2013  Berezin Stereo Photography Products